1 scope this specification shall cover the char acteristics of the ceramic resonator with the type zttce12.00mg50hd0f-r0. 2 part no. part number previous part number zttce12.00mg50hd0f-r0 zttce12.00mg customer part no specification no 3 outline dimensions and mark 3.1 appearance: no visible damage and dirt. 3.2 construction: smd ceramic packaging. 3.3 the products conform to the rohs dir ective and national e nvironment protection law. 3.4 dimensions and mark ? 3.20.1 1.30.1 1.0max 0.40.1 0.40.1 0.40.1 1.20.1 1.20.1 0.40.1 input ground output zttce12.00mg ceramic resonator http://www.luguang.cn mail:lge@luguang.cn
3.5 structure 1 2 3 4 5 no. components materials 1 outer electrodes top and bottom electrodes ag+ni(under plating)+sn(over plating) side electrodes ni+cu+ag(under platin g)+sn(over plating) 2 ceramic box insulation box 3 cover dielectric material 4 inner electrodes ag 5 glue epoxy resin 6 conductive adhesive ag+epoxy resin 7 ceramic element piezoelectric ceramics (pzt) 4 electrical specifications 4.1 rating items requirement withstanding voltage (v) 50 (dc 1min) insulation resistance ri, m ? min. 100 10v 1min operating temperature -25 85 storage temperature -55 85 rating voltage u r v 6v dc 15v p-p zttce12.00mg ceramic resonator http://www.luguang.cn mail:lge@luguang.cn
4.2 electrical specifications items requirement oscillation frequency fosc (mhz) 12.000 frequency accuracy (%) 0.5 resonant impedance ro ( ? )max. 40 temperature coefficient of oscillation frequency (%) max. 0.3 (oscillation frequency drift -25 +85 ) aging rate % max. * 0.2 from initial value *components shall be left in a chamber of +85 2 for 1000 hours, then measured after leaving in natural condition for 1 hours. 5test 5.1 test conditions parts shall be tested under the condition ( temp. 2015 ,humidity 6520% r.h.) unless the standard condition(temp. 253 ,humidity 6510% r.h.) is regulated to measure. 5.2 test circuit ic 1m c 1 c 2 v :+5v dd x ic output ic: 1/6tc4069ubp2 x: ceramic esonator zttce12.00mg ceramic resonator http://www.luguang.cn mail:lge@luguang.cn
6 physical and environmental characteristics no item condition of test performance requirements 6.1 humidity keep the resonator at 40 2 and 90%-95% rh for 96h. then release the resonator into the room condition for 1h prior to the measurement. it shall fulfill the specifications in table 1. 6.2 high temperature exposure subject the resonator to 852 for 96h, then release the resonator into the room conditions for 1h prior to the measurement. it shall fulfill the specifications in table 1. 6.3 low temperature exposure subject the resonator to -552 for 96h, then release the resonator into the room conditions for 1h prior to the measurement. it shall fulfill the specifications in table 1. 6.4 temperature cycling after temperature cycling of blow table was performed 5 times, resonator shall be measured after being placed in natural conditions for 1h. it shall fulfill the specifications in table 1. temperature time ?253 30 3 min 853 30 3 min 6.5 vibration subject the resonator to vibration for 2h each in x y and z axis with the amplitude of 1.5mm, the frequency shall be varied uniformly between the limits of 10 hz?55hz. it shall fulfill the specifications in table 1. 6.6 mechanical shock drop the resonator randomly onto a wooden floor from the height of 100cm 3 times. it shall fulfill the specifications in table 1. 6.7 soldering test passed through the re -flow oven under the following condition and left at room temperature for 1h before measurement. it shall fulfill the specifications in table 1. peak:260max 250 pre-heating 10s max within 80-120s. within 20-40s 30s min 230 150 100 to be continued zttce12.00mg ceramic resonator http://www.luguang.cn mail:lge@luguang.cn
6 physical and environmenal characterisics no item condition of test performance requirements 6.8 solder ability dipped in 245 5 solder bath for 3s0.5 s with rosin flux (25wt% ethanol solution.) the terminals shall be at least 95% covered by solder. 6.9 board bending mount a glass-epoxy board (width=40mm,thickness=1.6mm),then bend it to 1mm displacement and keep it for 5s. (see the following figure) support bar press head press mechanical damage such as breaks shall not occur. table 1 item specification after test oscillation frequency change fosc/fosc (%) max 0.3 resonant impedance ( ) max 40 the limits in the above table are refe renced to the initial measurements. zttce12.00mg ceramic resonator http://www.luguang.cn mail:lge@luguang.cn
7 recommended land pattern and reflow soldering standard conditions 7.1recommended land patter n :land pattern 7.2recommended reflow soldering standard conditions 3 h d n p d [ pre-heating v p d [ z l w k l q v z l w k l q v v p l q zttce12.00mg ceramic resonator http://www.luguang.cn mail:lge@luguang.cn
7 recommended land pattern and reflow soldering standard conditions 7.1recommended land patter n :land pattern 7.2recommended reflow soldering standard conditions 3 h d n p d [ pre-heating v p d [ z l w k l q v z l w k l q v v p l q zttce12.00mg ceramic resonator http://www.luguang.cn mail:lge@luguang.cn
8.1.2 section of package package is made of corrugated paper with thickness of 0.8cm.package has 10 inner boxes, each box has 1 reel(each reel for plastic bag) 8.1.3 quantity of package per plastic reel 3000pi eces of piezoelectric ceramic part per inner box 5 reels per package 12 inner boxes 180000 pieces of piezoelectric ceramic part 8.1.4 inner box dimensions 1852 1 8 5 2 962 no. name quantity inner box 1 qc label 1 label 1 zttce12.00mg ceramic resonator http://www.luguang.cn mail:lge@luguang.cn
8.2 on reel pack, the followi ng requirements are requested. 8.2.1 reel dimensions a b w t pieces per reel carrier tape size 180 3 60min 8.4min 12.4max 3000typ. 8 8.2.3 packing method sketch map blank pocket 10 pitches loaded pocket blank pocket 10 pitches leader 200mm max 8.2.4test condition of peeling strength p e e l i n g s t r e n g t h 2 0 - 7 0 g carrier tape top tape 10 max zttce12.00mg ceramic resonator http://www.luguang.cn mail:lge@luguang.cn
9 other 9.1 caution 9.1.1 don?t apply excess mechanical stress to the component and terminals at soldering. do not use this product with bend. 9.1.2 do not clean or wash the component for it is not hermetically sealed. 9.1.3 do not use strong acidity flux more than 0.2wt% chlorine content in flow soldering. 9.1.4 don?t be close to fire. 9.1.5 this specification mentions the quality of the component as a single unit. please insure the component is thoroughly ev aluated in your a pplication circuit 9.1.6 expire date (shelf life) of the produc ts is six months af ter delivery under the conditions of a sealed and an unopened package. please use the products within six months after delivery. if you store the products for a long time (more than six months), use carefully because the products may be degraded in the solderability or rusty. please confirm solderability and characteristics for the products regularly. 9.1.7 please contact us before using the produc t as automobile electronic component. 9.2 notice 9.2.1 please return one of this specifica tion after your signatu re of acceptance. 9.2.2 when something gets doubtful with this specifications, we shall jointly work to get an agreement. zttce12.00mg ceramic resonator http://www.luguang.cn mail:lge@luguang.cn
|
